Tecnoma KMAC KT2
Automatic Edgebander

• To maintain stability through the years, the structure of our edgebander has been constructed in stabilised electro-welded steel; this guarantees a secure and precise movement of the tracking which transports the panel to be edged, without any vibration.

• Panel movement system by an industrial large sized transport tracking, 70mm wide (so not to scratch the panel surface), sliding on 2 rounded guides in hardened and ground steel, to guarantee the maximum linearity in the movement of the panel and a high resistance to the side loads.
• Feed-chain pads in self-lubricating material with replaceable plates, vulcanised in a special resistant wear and tear rubber.

Panel holding system

• Steel pressure beam with large diameter rubber wheels with bearings, to obtain, during its movement, the maximum stability of the panel, including small size panels.
• Pressure beam adjustment by a chain system and a digital mechanical indicator to read the panel thickness.
• The working units position themselves automatically, changing the panel thickness.

Glue unit

• Alloy aluminium pot for hot melt glue with independent and adjustable coping movement.
• Glue pot coated internally with anti-sticking material.
• Speed rotation of the glue roller synchronized with the feed-chain speed.
• The spreading of the glue on to the panel is gauged by adjusting the glue distortion regulator.
• Any unused glue is automatically recuperated.
• Electronic digital thermo-regulator to set the correct working temperature of the glue.
• Glue pre-heating system when the machine is not being used, to maintain the glue temperature close to the working temperature, without burning it and saving time when re-starting the machine.
• The electronic thermo-regulator enables the temperature of the glue to be automatically lowered in the event of temporary interruption of production.

Edge feeding unit

• Automatic feeding of the edge in rolls/coils up to 2mm thickness.
• Manual feeding of the edge in strips up to 2mm thickness.
• Shearing device for edge in roll/coils up to 2mm thickness with quick "off-work" system.

Edge pressure unit with 2 pressure rollers

• Adjustable, changing the edge thickness, with a mechanical digital indicator.
• Both rollers are equipped with spring pressure.

End trimming unit

• Pneumatic, with knife, to cut, 90degrees, the excess edge in front and behind the panel.
• The cutting group moves on hardened and ground steel guides.
• Cut from the side of the panel, to prevent that the edge cuts do not disturb the working parts of the unit.

Top and bottom edge trimming unit

• 2 high frequency motors to trim the upper and lower edge in excess.
• The operating unit automatically positions itself when changing the thickness of the panel.
• Unit slides vertically and horizontally on hardened and ground steel guides with recirculating ball-bearing bushes to guarantee the maximum working precision.
• Vertical and horizontal thick chrome coated copying shoes on each cutting unit.
• Adjustable copying sensibility on vertical and horizontal floating movements.
• Adjustable cutting position by mechanical digital indicator.
• Quick release (electrical and mechanical) of the motors to facilitate work change.
• Included, one pair of radius cutters R=2mm with replaceable TCT knives.
  

	0.4 - 2mm
	1 - 2mm

• E.C. Safety regulations.
• Static high frequency converter.
• Protection cover - centralised dust extraction
• Adjustable rollers support for large panels, to the complete length of the machine.
• Protection/copying plate in front of glue roller.
• Control switches on the panel in-feed position, easy to use for the operator.
• One pair of radius cutters R=2mm with replaceable TCT knives.
  
  

---

 

Technical Data
Edge thickness in rolls	0.4 - 2mm**
Edge thickness in pre-cut strips	1 - 2mm**
Working height	10 - 45mm
Minimum working width	65mm
Minimum working length	180mm
Panel feed speed	5mt/min
Static high frequency converter	200Hz
Centralised dust extraction hood diameter	2 x 80mm
Extraction quantity required	450 mc/h
Pneumatic system pressure	7 bar
**2mm thick edges for a panel thickness max. 25mm. With thicker panels max. edge thickness 1.5mm
Glue pot
Heating power	2.4 Kw
Front and rear end - trimming unit
Pneumatic, with cutting knife
Top and bottom edge trimming unit
Power of each of the 2 motors (200 Hz)	0.35 Kw
Cutters rotation speed	12,000 rpm

 

	A 2450 mm B 1310 mm C 1270 mm Kg 580

Price
£6,995 + VAT